Skip to content

How I Connected My Guitar to FL Studio 12

I just recently purchased my first guitar. It’s a beginner level Yamaha ERG-121C that came along with a starter pack – basically an amp and some few accessories to get someone jamming right away.

Soon, however, it dawned on me that the basic amp it came with (a 19W Yamaha GA-15), while decent enough for my amateurish needs, wasn’t doing much for me in terms of tone options.

To top it off, I wanted to play the guitar through my computer’s headphones, as it’s much easier to play along a song that way.

That’s when it all occurred to me I could use a copy of FL Studio that I never got around to using to achieve much of this inexpensively.

Basically, it would act as both a “virtual” amp and an effects plug-in so that I could get a variety of tones. This is how I went about it.

Step 1: Connecting the Guitar to the Computer

The following is a very cheap starter way of connecting an electric guitar to a computer. Of course, if you have or can afford a good sound card/audio interface then I assume you
already have this part sorted out, and so you can skip to the next section.

My main machine is a Dell OptiPlex 380 tower and I make use of its integrated sound card (Realtek ALC269) for all my audio needs. It has 4 audio jacks:  a mic-in and headphone port on the front and speaker (line-out) and line-in ports on the rear side.

In my case, I intended to connect the electric guitar through the line-in port on the back, though the mic-in would work too.

Since the line-in port measures 3.5 mm, it’s obviously impossible that I could connect the 6.3 mm guitar cable jack directly into this port. To get around that, I bought a 6.3 mm female to 3.5 mm male jack adapter that set me back a paltry $0.40.

A picture showing a 6.3 mm female to 3.5 mm male jack adapter

The rest I think is self-explanatory. I just connected the guitar jack into the adapter and plugged it into my line-in port.

Even in this rudimentary set up, the guitar’s clean sound was already audible through my speakers, albeit very low despite the guitar volume knob being maxed out. Increasing the line-in boost (dB) from Windows sound settings did however help.

I could even make some decent recordings with Audacity using this simplistic set-up. All you have to do is set the input line-in, and you’re good to go.

Step 2: Connecting the Guitar in FL Studio

I’m using FL Studio 12 so that’s what I’ll use for this guide.

  1. With your guitar connected to your computer or laptop, launch FL Studio.
  2. Make sure the Mixer is visible inside FL Studio. If it’s not, toggle it by pressing F9 on your keyboard or by activating it from Toolbar > View > Mixer.
    A screenshot showing the mixer menu item in FL Studio
  3. On the Mixer’s top right corner, you should see the Audio Input Source drop-down menu. Click it to reveal the input options which will vary with your individual setup. Mine lists 3 input sources as follows (I think it might be necessary to have installed ASIO4ALL when installing FL Studio for this to work):
    • FL Studio ASIO – Stereo: In 1 – In 2
    • FL Studio ASIO – Mono: In 1 and In 2
      A screenshot showing the Audio options in FL Studio 12.
  4. Try every one of those input sources and find one which picks your Guitar. On my computer, all three do pick up the guitar, but the mono ones sound a tad better compared to the stereo one.
  5. For the output, check beneath the slots for the Audio Output Target menu. On mine, it’s automatically set to the only option available there: FL Studio ASIO – Stereo: Out 1 – Out 2
    A screenshot showing the Audio output traget in FL Studio 12.

Step 3: Using FL Studio Guitar Effect Plugins

The Guitar should now be sufficiently audible through your speakers or headphones, however the sound at this point is still clean.

If you want to increase the distortion or play around with some effects, you’ll first need to activate the VST plugins as follows:

  1. Just below the Mixer’s Audio Input Source there are about 9 effects (FX) slots. Click on the first slot and that should open a pop-up menu with a long list of effect plugins.
  2. Take your pick from those effects, but if you find that task too overwhelming, I recommend starting with Hardcore. It has plenty of guitar tones presets; everything from Blues, Classic Rock, Country to some crazy distortion levels with the Death/Doom metal ones.
  3. If you want, you can add more effects on the remaining slots and mute/activate them at will using the little green light buttons on their sides. The effect levels for the individual plugins can also be adjusted using the knobs beside the slots.

Beyond these plugins, I’m guessing one can also use the generators (like the FL Slayer one) or in tandem with the plugins, but I’m yet to figure that out clearly.

Lastly, should you want to do some recording while playing, just use the record button in the top menu.

A screenshot showing the record button in FL Studio 12
Record Button

So that’s it. Now how about you stop reading this and go make some noise for your neighbours.

Share:

Leave a Reply

Feel free to share your comments or questions with me. I may not be able to respond immediately so please check later once I've approved your comment.

Your email address will not be published. Required fields are marked *

Kelvin Kathia

Kelvin Kathia is a writer that's passionate about sharing solutions to everyday tech problems. He's the founder and editor of Journey Bytes, a tech blog and web design agency. Feel free to leave him comments or questions regarding this post, or by leaving him a message on the contact page. If you found his content helpful, a donation is much appreciated.